Protecting The Chrome Jewels

Advertisements

On a recent visit to a good friend of mine who also owns a rather nice and rare coloured Mustang Convertible I was shown around his latest collection of Mustang memorabilia where I spotted in middle of his (man cave) garage a dehumidifier. He went on to explain the benefits of it and I could feel the air was different to mine at home. that was it, I was sold on the idea and set about getting one. So I done a little research from various places and found these points where I have collated them and made them a little more readable, I hope. I have since seen references to classic cars with lots of chrome like mine as the “Chrome Jewels”. I quite like that sying in fact. Many storage companies of classic cars all have climate controlled environments.

Rust will form where the surface of the steel has air and water. The first step is to stop the elements reaching the steel, paint does the job pretty well, but even better is wax or  similar coatings, or Waxoyl etc. Chrome is surprisingly porous and normally underneath the chrome plate is steel so it needs protecting. A covering of wax, ordinary car wax or Gibbs, will do the trick, it looks invisible, adds shine and protection. Don’t forget that a chrome cleaner is generally abrasive and removes any wax coating, by all means use it to clean, but it doesn’t protect the chrome.

Don’t get to hung up about the temperature vs humidity, as it’s often being mentioned to keeping humidity below 50% to stop rust, but it’s a bit more complicated than that and one of the keys is understanding about “dew” points. All air contains water and as the temperature drops that water tries to change back from a vapour to a liquid, that’s what causes rain, warm moist air pushed up by the weather cools and the water in that cloud becomes a liquid which is heavy and falls out of the cloud – rain. In your own home you see it as condensation around bedroom windows on cold mornings. It is around the window because that is normally the coldest part of the room.

There are 3 ways to fix condensation:

  1. Heat the room so the air inside can hold more water.
  2. Open the window (ventilate) in the hope that air coming in from outside will be dryer and therefore hold more water.
  3. Use a dehumidifier to reduce the percentage of water in the air.

The theory of condensation effect is to take a can of cold drink from the fridge and put it on the table or work top. Even in a warm house you immediately see condensation on the can as the water in the air rushes to the can and condenses back into a liquid. This is the same principle as how a dehumidifier works, you present a cold surface to the air, the air in turn gives up its water which is then collected in a container. The fan in the dehumidifier keeps an airflow over the cold chilled surface so as much air as possible reaches the cold surface.

Back to my Garage; heating the space to about 20c works well (in fact any heat helps) because the higher the temperature the less the water has a chance to condense back to a liquid. This is why I fitted a radiator in my garage, much to the bemusement of my wife! unfortunately it’s not the complete answer though. Another example of the condensation is that you get condensation in a bathroom after a long hot shower even if the air temperature is 25 or even 30c. You could indeed heat a normal garage to 20c, the car would sit in there and not deteriorate, but even with insulation that is expensive way of doing it. Hence why the US “dry State” cars are so popular in UK as there is not much chance of the rust taking hold in the past.

I have done all the usual things; The heating and water boiler is in my garage and gives of heat to the room as the hot water passes through the pipes. I have insulated as much as possible, the walls are cavity filled, the ceiling has plenty of insulation up there and the all important plastic floor to stop the cold coming up through the concrete. The up and over door has brushes to keep the draft out and the back of the door has heat insulating sheets. That way I should then be able to keep the space at least 9c throughout the winter with no additional heating and that is obviously a big help.

On the other hand, when you open the garage door the same thing can happen on a warm moist day, the air rushes in and condensation forms on whatever is coldest part in there, that is mostly going to be your prized possession, your car. I found this rather good chart to show the relative ranges of humidity and what I am trying to explain:

So I have bought myself a dehumidifier. I have reviewed it here and is also under the accessory menu on the main bar. I wanted two things from the non-negotiable options. An option for constant draining and the low-cost of running it over 24/7 scenario. The options were a little limited for my modest budget.  I managed to pick up a well rated PureMate PM412 for a modest cost of £120 reduced by sixty pounds from the recommended retail price. I also purchased a digital humidity gauge and left it in the garage for a couple of days to get a reading. There is a max and min scale for both the temperature and the humidity. The gauge is on top of the car in the middle of the garage.

The unit is compact and neat looking with a capacity of twelve litres a day. There is a digital read out and super simple to work and set up. The gauge above shows the first night was 45rh to a max of 50rh which I was super happy with.

The unit has a castor wheels and a recessed handle which is so easy to move around. There is a one meter length of tubing they even supply for the constant drain should you need it which I will of course. The ease of movement makes it ideal to shove out-of-the-way in the corner of the garage when working on the car.

The collection tray can hold one and half litres of water, and over night I think it was up to about a little under a litre. So I am having to empty it morning and evening now until I plumb it in. But, that is the unit settling the environment down then they should reduce considerably after a few days. It doesn’t matter if I forget to empty it as the unit will shut down when the tray is full.

The power consumption os a max of 245w on full power, but as I only ran mine on a low setting it should work out quite economical to run especially as it will be on all the time. Has anybody else got any tips or tricks they would like to share storing their car over the winter? Please post a reply and we can all share the knowledge.

Roll on the spring so I can take the car out for a drive. I have an itch I can’t scratch when I can’t drive my car.

Error happened.
Share my Content

Making Headway

Advertisements

Looking forward to the long weekend as I could get to Mustang Maniac on Saturday and rest for a day on Sunday then do some homework which I had in mind on the bank holiday Monday. Saturday morning I loaded up the car and went to the garage to pick up my sockets and tools bag, I walked in picked up the stuff and put them in the boot and shut the garage door. Realising I forgot the ratchets I went to open the door Again. Locked. I searched my pocket, no keys. I went to the back of the car and checked the tool bag, no keys. I then had the cold sweat feeling, I put the keys on the service trolley in the garage. Now I always unlock the garage, lock it again and put the keys in my pocket. That way when I shut the door it’s already locked and so I don’t forget. Get the spare key, there is no spare key! When we bought the house there was only one key for the garage and I have been meaning to get one cut ever since for a number of years now should we say. At this point it’s dilemma time, do I try to get into the garage or leave it until Sunday? I decided to leave it, and went to say goodbye to the wife who could hear me havin’ my own little rant to myself out the front. She didn’t laugh (yet), but used some of the words that I was using previously to describe my stupidity back to me. Her stifled laughter didn’t last to long as I got in my car with the right hump. All sorts of things were running through my mind, locksmith? Replacement door? I just didn’t know what to think, all the way to the yard I was fretting and nothing on the radio calmed me down, cyclists two abreast down country lanes gave me the hump, getting stuck behind a bus down country lanes gave me the hump. Eventually I got to MM and bumped straight into Adam and Chris. I explained what I had done with my garage, they explained the best way to “re-gain entry” back into my garage when I got home. How do they know these things? Anyway, Sunday I tried their techniques to open the door. Now I needed a replacement part, I took the old one with me and took it to place I know who stock all that sort of stuff. Got home and replaced the handle and lock with a stronger quality one. All fixed again and now I have two keys.

Tip:

If you need another key, get one cut before it’s to late!

I unloaded half the tools I normally take to the yard and went to the workshop. Where Adam showed me the head liner that had been fitted. It looks great and gives it new lease of life. There were a couple of fold marks near the edges that would drop out shortly under the pressure of the headliner bows. I was well pleased and decided to go for a celebration Cherry Bakewell cake with the guys in the boys club.

Next was some exhaust work, as the parts had been sprayed last week and they were waiting for Yogi who didn’t get a chance to re-hang the exhaust as he was busy on other cars. So as I watched him last week I had a go myself, I soon realised it’s not as easy as he made it look. I eventually got it all back in place and aligned it up best I could get it. Just in case Yogi wanted to move bits I didn’t clamp it up hard, but just a tiny pinch to hold the brackets in place. There was not a lot of room to manoeuvre under there but it’s hanging in place and ready for Yogi to do his thing with the three-inch headers to the main pipes. I know they are not aligned up square and neat, but they will do just for now.

The next part was the carburettor fitting, I removed the old tape from the inlet port that kept the area clean. I rubbed the area down clean ready for the gaskets to be fitted back in place. John joined me and we worked out the sequence of gaskets to be fitted. The first gasket was to seal the intake to the carb spacer.

Then comes the carb spacer, not essential but these give extra torque and power to the engine and make things run that much nicer. This spacer sits on top of the previous gasket.

The next part is the gasket for the bottom of the carb and then the car itself.

The sits on top and is bolted down for bolts each corner.

With the carb in place the throttle linkage was connected to the butterfly controls of the carb and the vacuum advance line. I’m not sure I like the pipe and may change that to look neater.

Adam joined me late in the day we got to grips with the pipe work. We fitted up the new black silicon pipes with my new clamps which turned out to be a real pig to fit in position due to the bulk of the T-bar fittings at the top. We eventually got there but I needed to order two more clamps for the top hose. The clamps should have fitted, but they wouldn’t fit over the pipes and the ridge at the end of the water pump. I will order the next size up they should be with me by the time I get to MM next week.

Feeling a little worse for wear at 7.30pm we decided to call it a day. I had forgotten all about my locked up key, that was until I got on the dual carriageway, put the car in cruise control and reflected on the day, what a stupid boy I had been I thought to myself. OK I didn’t use those exact words but it sort of means the same thing.

My homework? Well that was to bring home a wheel and tyre from my collection. Adam tells me I had different steel wheels from different cars and only one of which was a Mustang wheel. The wheels were welded on some, riveted on others, different sizes and slightly different designs all that I hadn’t noticed. The only good bit about it all was that the Mustang wheel had the best tyre of the bunch on it. I will clean up the wheel and use that for my spare should I ever need it that is.

Error happened.
Share my Content

Going, Going, Gone!

Advertisements

Saturday was a big day for me that I have been waiting a long time for to be honest. The day the car was going to Mustang Maniac for the heavy restoration parts. The rear quarter needs to go on, a few bits on the chassis need to be welded up, the engine and gearbox will come out and be prepared for the paint, all of which I can’t do myself. My car was to be picked up by John from Mustang Maniac in a LAR Recovery services lorry. Eight o’clock I was ready, the car was pushed out of the garage, all the rubbish inside had been removed. The additional parts of the painted valance and stone guard I done were inside the car laid out lovingly on old towels and the hood was resting by the car. Then I waited for what seemed like hours, every car was “the lorry”. I was pacing like an expectant father outside a delivery suite, what on earth was wrong with me? I went inside for a cold drink as the weather was warming up nicely and turning into a gorgeous day. Typically no sooner had I poured a glass of fruit juice and the lorry turned up. I ran outside and greeted John and the kettle was ready for the mandatory cup of tea. John had a wonder round my car with his tea and looked her over as I was waiting nervously for the sharp intake of breath, there was none I am glad to say, although he had spotted the bits I knew about straight away.

The lorry curtains were mechanically wound back to expose the bed. The bed was slid rearwards and eventually lowered down to form the ramp. We pushed the car into the road and lined her up to the bottom of the ramp. John latched the straps to the front chassis which was in turn attached to the winch at the front of the bed.

Slack was taken up and gently pulled up to the bed. I was making a few small turns to the steering wheel to make sure she was on square. little by little she was moved up until the weight was over the lorry axle on the bed. John lashed down the rear wheels securely to stop any movement during transit.

The bed was then lifted horizontally again and slid back towards the front into place on the lorry. Within seconds the curtains were rolling back to encase her like the curtains closing at the end of a play. There she was in her own little world, all we had to do was load the hood onto her old carpet and shut the rear curtains.

Ladies and Gentlemen the Mustang has left the building!

  • Special Thanks to Adam at Mustang Maniac for allowing me to use their photos on my blog as well, all the pictures are on their blog here.

After the trip to the Mustang Maniac the process was reversed and lowered into the main yard, the car was pushed onto some ramps for the initial look for anything major to report.

After the inspection she was lowered down again and pushed into her new home for a while – Mustang Maniacs panel shop!

Emotions running high, I know she has gone to a better place. In time she will look like new and be back home. I still have a few parts here and there that will be cleaned and ready to go back on when she is ready.

  • Special Thanks to John for taking such good care of my car.

Quick Links:

Mustang Maniac main web page click here

Mustang Maniac blog pages click here

LAR Traffic services click here

Error happened.
Share my Content

Shocked & A Little Hacked off

Advertisements

The weekend has been busy for me again. The wife is so busy I can hardly get on my PC, so I have resulted in using my Galaxy Note 10.1 tab, bluetooth keyboard and a shared internet connection. Everything takes that bit longer unfortunately, but at least I can still work on my blog only at a lower pace. Anyway, as I hadn’t seen Adam for a few weeks I made my monthly pilgrimage to Mustang Maniac, the excuse I made was, “at least I will be out of your way!” With that the “Day Pass” was issued, gratefully accepted by yours truly and I was off. Once I arrived I was speaking to the guys who were showing me the new improvements that were going on to cope with the demands for their work. I believe a blog will be coming out about it soon. After a good few hours of chatting, meeting people coming into the office and watching a few last-minute repairs on a customers car by fitting of some nice LED bulbs to the side lights on a ’66 coupe. I had a wander round the stock rooms. I spotted some rear shocks that had just arrived so nabbed a pair of them pretty sharpish and immediately decided what was going to be my new project for Sunday.

My current shocks were a gas adjustable pair, the only problem is, there is no plumbing for the right hand side and the left hand side is seized solid. I knew these had to be changed regardless, and as the wife was still working, I took tools along with my new shock absorbers out the garage to get some work done. I have written a full process for changing the shocks under Photos Menu – Rear Shock Replacement or click here for the quick link. To cut a long story short, if you pardon the pun, I ended up having to cut one side of the old shock stem off with a hacksaw, in order for me to get it out of the bracket. Not exactly proper mechanics, but as I wasn’t going to keep the old shocks it didn’t really matter. The trouble is it just doesn’t look good with a pair of legs hanging out the front of a garage with that distinctive sound of a hacksaw on metal. The new shocks were a performance rated pair, and according to Adam they are a lot of shock for not a lot of money. On top of that they looked quite good too being all in white. The only thing I could say was that I was worried yet again by the fact that the previous efforts of the “Herbert” to restore this car were a bit of bodge job to say the least. Spanner points rounded off, nuts loose on top of the shocks and at the bottom, old parts just left in the recesses etc. What else am I going to find? Plenty I expect, but don’t worry, I will let you know when I do find something else!

After all the work was done there is nothing quite like replacing parts that look good and can be seen by somebody else for a change, and above all, these parts will do the job properly. I was well pleased with the weekends work in all. The car no longer bounces like a baby cradle one side and up on stilts the other side. In fact I far from hacked off, even though I had to do some to get the job done. 🙂

Quick Link:

Photo Menu – Rear Shock Replacement click here.

Error happened.
Share my Content

Dual Master Cylinder Project

Advertisements

I worked a long day on the car over the weekend and I managed to complete a project that I wasn’t planning on. My original master cylinder produced a leak during the bleeding process. So to cut a long story short I upgraded to a Duel Master Cylinder System. Ok, my car is not concours original anymore, but I intend to drive and enjoy it not just show it, clean it and be unable to enjoy it because of the spec of dust on the exhaust. It has taken me most of the evening to write-up the process and pictures, but I am pleased with the results and wanted to share it as promised in my previous post. I have now posted the project under Photos – Engine bay – Dual Master Cylinder Upgrade, or click here for the quick link. This is no ordinary upgrade though, this kit includes a rear proportioning valve, built-in rear pressure valve and an inline pressure valve for the front brakes. Disc brake ready!

Next weekend I hope to bleed the brakes or at least try again.

The only side effect to my long day on the car was I felt like I had my legs run over by a bus. All that stretching and leaning over the fender took its toll on my hamstrings. Is it that I am getting old or should I have done some stretching exercises first? Yeah, like I wouldn’t look like a doughnut doing exercises in my garage to change a master cylinder! Us blokes don’t do that sort of thing, but I might just do that behind closed doors next time. 🙂

Rust

The recent bad weather has been doing wonders for the Rust test that I am still performing. The comparison is between the Granville Rust Cure and the FE-123.  I will continue to run the experiment a while longer then I will post some pictures and results so far. I intend to do a long-term test and keep coming back to it with updates.

Error happened.
Share my Content

Late night on the car

Advertisements

Today was a mental busy day, the sun was out the birds were singing and I was bashing and clanking in the garage. I have spent all day and few more hours into the evening doing my upgrade. I have taken out the old leaking master cylinder and replaced it with a new Dual Master cylinder. Yep, last week I went down to see Adam at Mustang Maniac and got myself a new set up. The parts took a little while to find amongst the organised chaos there of the massive delivery of stock. I was a little worried about the fact there was a single cylinder that does all the brakes. If the single cylinder leaks then I lose all braking, not good. So it was a no brainer really to get this in. OK, again it’s not concourse for the car I know all that, but it’s safe or will be once its done. I have taken lots of photo’s for the project and what had to be done, I will upload them and write them up this week sometime, watch this space. All I am saying is I needed more copper pipe, lots of it!

Why didn’t I do it yesterday? Simple, remember that rotten ol’ (OK, it’s new but I don’t like it because of the hassle it gives me), summer-house I was having fun with? Well I finished it off yesterday. It was a total nightmare to say the least. The glass was cracked when I opened the packets up and the latch had the bar missing inside to go to the inside handle. Just what I needed, NOT. I put the rest of the glass in that I could and panel pined the beading on. Now to me, hammers and glass don’t go well together and I was so carefull not to break any more glass, hardly ideal. Give me metal to sort out anytime!

But, next weekend is a Bank Holiday, that means I will be doing car stuff only, no sheds, no fences, no summer houses, no weeding, no patios, no nothing except my car. That is unless the better half decides I need to do a few jobs to make up for the money I spent on the brake cylinder. I admit it – I dare say one of the days will be me doing jobs for her. I may wear the trousers in this relationship – but she gets them out for me to wear! 🙂

I have attached a picture of the finished Master Cylinder as a little teaser.

Error happened.
Share my Content

Like buses…

Advertisements

They say that buses don’t turn up and when they do there are two of them! I never really understood that as they should be on a time-table, but it does happen. Anyway the point is similar with me on the blog this weekend. I only posted a little quote in the last couple of weeks and this weekend I am posting twice with a full set of photos for work I have been doing on the car. OK so this post will not be as long as the last one but it here never the less.

Today was a day in the garage, I was going to finish up the hand brake cable on one side, so far the other brake has been restored yet. Then I was going to get in the engine bay and treat some light surface rust I had in there. I was on a roll and got to work the hand brake was dismantled again and some grease was applied to the parts that were metal touching metal. Although this sounds simple, it wasn’t as it required a certain technique, the car is on axle stands at the rear but not very high up. So as I needed to get to the back of the gear box effectively there is not much room to slide under the car. So the technique is lay sideways onto the car, turn the head sideways and shoulder shuffle untill the shoulders are under. Then bring the arms above the head then in the same manoeuver place the feet against the wall. Timing is now crucial, exhale and push with the feet while doing the shoulder shuffle thing. Once under, the tunnel provides a little welcome space and the rib cage is now able to move a few shallow inches at a time. Everything has to be to hand in order for this to work mind you. At this point I’m trusting those axle stands can really hold two tons as they say they can, if they fail, I am gonna get crushed ribs and all sorts of other unmentionable injuries, if I am not killed anyway that is. Getting out is a reverse shoulder shuffle out and slowly turning the body a few degrees so you exit sort of parallel to the car, those next few deep breaths feel so good. I do have bruises to prove that it was honestly that tight under there. It took me a while to get the hang of it, but I got it off to a fine art now. So the hand brake was in place it works (sort off) as the new parts are linked up to where they should be but not yet adjust correctly. Next job was the engine bay, I got my new stuff Rustbuster FE-123 that I am using to see what that is like. I am planning on doing a comparison test with the Granville Rust Cure and it’s all underway now being left to the elements as I type. Hopefully that will be a video review and then blogged later with my comments. The de-rusting painting was going well, the sun was out, the birds were singing and I was enjoying myself. A couple of kids went past on the their bikes and I watched them go past thinking nothing of it. A few minutes later they were back this time there were four of them, varying from eight to twelve I would say. They stopped in the road (it is a tiny little dead-end where our house is so they were safe enough) and looked at the car in the garage. The first one and the eldest said “Woaaah, Is that a Mustang? Yep it is”, the second said “Go and ask that bloke how much he wants to sell it for, and then tell your dad and he can buy it”. I was taken slightly aback as I didn’t reckon they would be able to pick out a classic Mustang from a done up Jap Ricer with a fake exhaust and a fluffy dice in the window! I was well chuffed.

The view they saw?

At home

Photos:

I have added a photo set of my Drive shaft removal and refitting with oil seal change or click here for the quick link. I am in the process of writing up the Rear Brake Drum refit Parts 1 & 2 as well. There are links to those pages from this photo set, but they are being updated over the next few days or so. I have been able to get a fair bit done on the car and taken plenty of pictures to so I can add them to the blog.

Error happened.
Share my Content

The fitted sheet

Advertisements

Friday evenin’ and it started.

I of course refer to the snow, no I am not going to bang on about it again because I am to put it politely, getting a bit sick of it. Everytime I want to do something it snows. The snow has been falling all weekend, it settles then it melts, still snowing then it settles again. Global warming? I think it needs warming up round here, so I better go and start my v8 up with no exhaust and let it tick over for a while! Only joking, so I won’t dwell on the fact its cold, but my man cave looked like a log cabin at one point today with the snow all over it, and it did get worse than this. To prove it I have a little picture of it. I’m sure there are a lot of people worse of than me out there, I hope you are all safe and have had not issues with the “S”. Don’t forget to check on the vulnerable elders, even a pint of milk for a hot cup of tea can help.

Man cave in the snow

Saturday I sprayed the VHT brake caliper spray on the left side front drum which went well, I keept the can in the house overnight in the warm along with the drum itself. I only took it out to the man cave when it was ready for the spray. I pointed my new light at it to keep it warm during the drying phase. It worked a treat. After it was dried to touch, I took it to the garage and put it onto the spindle and packed it with grease. I will allow it to cure for a week before the wheel gets bolted back on. I have already done a review of the VHT Caliper paint under the Reviews – Consumables or click here for a quick link. I also went to fit the brake booster, it was going in OK, but as I was so cold the fingers were having issues holding things properly. I got a bit annoyed at this point and decided to take the hood off so I could get right into the corner. Oh boy, I forgot how heavy that hood was, trying to hold it in place with one hand and undo the nuts with the other was not an easy task. Thankfully nothing was damaged and it came of with a big sigh of relief and a lot of effort. I did remember to put some heavy towels onto the cowl under the hood corners so it would suddenly drop metal onto metal. The hood now sits against the wall ready to be treated, to top it all, hood is of course standing on a nice piece of foam. While the hood is off I took photo’s of the brake lines, (before I re-fitted the booster again), that I fabricated a while ago along with photo’s of the Brake Booster being fitted. After gaining access to the full engine bay the Booster actually went in fine, all was well with the world again. As there is no protection for the engine now from the hood, the dust from the garage could be an issue so I decided it needed covering. Did you know that the fitted sheet from a UK double bed is the same size as a 66 Mustang engine bay and fenders. Next time you play Trivial Pursuit you can maybe win on that bit of knowledge, OK, maybe not. I will be covering the treatment of the hood at a later date with pictures too when the weather gets better as it will need to be layed flat. To show you what I mean about the fitted sheet, here are the before and after pictures. Liking that? OK, Sorry then, but I thought it was a good idea!  🙂

The bits that are sticking up are the hood springs, they are gonna stay like that, due to the fact I want to keep my fingers and they are super strong springs and may have difficulty getting them up again. The scissor action on the metal is sharp and I never put my hands near them, ever! I managed to also remove and re-assemble the Hood catch, the pictures will be added to the photo section as soon as I get them done, they also came up very well. In the engine bay picture you will see the Brake booster in place and the reservoir all connected up. You can find the fitting in Brake Booster Part 3 in the Photo Menu – Engine Bay – Brake Booster Project or click here for a quick link. I have also added a review of the Autolite Group 24 Replica Battery now after a request for it and a few searches, you can find the review under the Reviews – Car Parts section, or click here for a quick link.

All in all I was quite pleased with the weekends work considering it was….. Ha, you thought I was going to say the “S” word, you know “snowing”. Dohhh!

Drive safely.

Error happened.
Share my Content

Making up for lost time

Advertisements

The weekend took forever to get here and once it arrived it only paid me a fleeting visit.

The last two weekends have been busy with Mother’s Day and birthdays. On both occasions I was delighted to go shopping and not spend that special man & machine time that only petrol heads understand. Saturday started with the left hand front brake drum, it was de-rusted and had two coats of Rustcure applied. Next weekend it will get the VHT caliper spray applied. I also managed to do a few jobs in the garage. The main one was to cable clip the solar power charger cable to the wall. This was going fine until I got to the front of the car. Now the car just fits in the garage and I have to squeeze around the front to get the other side. This is a carefully controlled operation as the front of the car is on axle stands and there is no protection around the hood catch. I mention this as the hood catch is around the same height as my man equivalent of, two sockets and a ratchet. On squeezing past the open hood in the middle part, there is a sharp corner that caught the standard issue jogging bottoms and ripped a little hole. I was waiting for the pain and the feeling of blood. Carefully I checked all was in place and making sure there was no damaged areas that the cold was masking. Now from a distance it may have looked strange a man rubbing his socket set in front of an open hooded car. I know that 289ci engine is pretty good, but I don’t think I would go that far! After the near miss I decided that the hood catch would also be coming off too. I got the proper tools and it was off.

Sunday was strip down of the hood catch and treat it. The photo set can be found under the Photo menu, Bodywork, hood catch or click here. All was ok apart from a few rusted bolts that needed a little persuasion to come out. There was no horrendous rust on there and it just looked worse than it was, in fact it was quite solid. I had set the alarm to come inside and watch the first race of the season Formula 1 in Australia. I put my headphones on so I didn’t disturb the wife. It was a good race and pretty even with an unexpected winner which makes a nice change. After the race had finished I picked up the blog on my Tablet PC, I edited some photos and created a page(s) for them. I have also uploaded my review of my Halfords Advanced Pro 120 Socket Set under Tool Reviews or click here.

Why was I able to do all of this? Saturday the wife went shopping and came home to do some work and online banking. Today she has been at my PC all day doing various things, and marking books. As she has been busy all day and I have kept out of her way. Let it be said that although teachers have long holidays, they spend most of their time planning, organising and marking. I have hardly seen her this weekend. For me that’s a sad thing, as we haven’t even managed to curl up and watch a film like we love to do at the weekends. For me it’s been a strange bitter-sweet day, lots done on the car, but I really haven’t seen my wife. Throughout the weekend she will usually pop out to see what I am up to at least a couple of times a day. I feel sad for her as she hasn’t seemed to of had a break.

back of nood catch
Error happened.
Share my Content

Lighting the way

Advertisements

The weekends are short and the weeks are long, some are just to long. This past week has been one of those weeks you want to forget. Lack of sleep made me a bit cranky to be fair, so obviously a lay-in was on the cards on Sunday. As we live in a sleepy little village where the front page of the village magazine would be number 57’s cat found safe and well after being missing for 5 hours. Things are usually very quiet, during the week and weekends and I expect nothing different this weekend. 8.45am Sunday morning I was awoken by the sound of electric hedge trimmers. Why this elderly gentlemen decided to do trim his hedge at this time is beyond me. The guy is retired and he could do that any time during the week when us poor workers aren’t about. Should he have been more considerate or did he just not think of others? I would not cause bad feeling about it but it would have be nice to have had the rest. I was up early Saturday as we had things to do, so Sunday was going to be my rest day, alas it was not to be. Are layin-ins a thing of the past now days?

Earlier in the week I had ordered a light, not any old light, but something I had thought about for a little while now. Working on the car in the garage was a little difficult as the light bulb was in the middle of the garage, when the hood was up there was a horrendous shadow over was in the engine bay. I decided on a site light, this is a halogen bulb on a stand that is height adjustable. The reason behind it is that I can move the light where I want it around the car and also take it out to the man cave and work in the evening. I will review the Faithfull light and put it in the review section very soon. As I was out Saturday with the wife and my mother-in-law to get some replacement ceiling cords, we were looking around and I found a cheap wall mounted halogen unit almost as cheap as a the replacement bulb, needless to say I bought that and put it up today. Now I have a nice spot light straight into the engine bay. I have gone from a single 60w bulb to two lots of 500w lights. I’m not saying they are bright but Boeing have made a couple of detours from the normal flight path towards our house, not really but I wouldn’t be surprised. In fact I may get some lower wattage bulbs. Due to such a mental busy weekend I haven’t done half of what I wanted to do. But I have managed to put a final coat on the brake drums with VHT caliper satin black. I will review the spray soon too as it gave great results. I have taken photos and a video, which one I post I’m not sure yet.

5th March 2013 update:

I have now added the review of the Faithfull 500w Halogen light in the review section or click here for a direct link.

Error happened.
Share my Content