Need I say where I was over the weekend? Yep, Mustang Maniac to take the final parts off the car. The front and rear glass was to come out and I was little nervous about that to be honest in case I cracked one. There are two ways to get the glass out; the easy way and the hard correct way obviously. The hard way is to fold the rubber back a bit at a time and lift the glass out, it takes time, patience and luck not to crack any brittle glass. The principle is the same for the front and the back glass. We looked at the car and decided that the rear rubber was showing signs of age and a few splits in places, this one was going to be the easy way. The front was going to be a pain though. The front has either been replaced or the original put back in. The reason I suspect is that they were trying to find a leak inside the car. This leak was enough to make them take the rubber and glass out and seal it all back in place with copious amounts of mastic. They must have shares or own the company looking at the amount they used. Anyway, due to the mastic there was no way I was going to be able to save the rubbers at the front although they didn’t look to bad. The easy technique is to lift a flap of rubber that is over the top of the glass insert a sharp knife at such an angle to cut the top rubber section of the bezel of as it were. Once the rubber is cut of you can just lift the glass out, but first you have to free it from the rubber by gently tapping it up with your hand. The rear was simple and straight forward and came out without any issues. The front on the other hand was a pig of a job; the mastic was so thick I had to do it small stages and very slowly to avoid putting too much pressure on the glass. Eventually it was all cut away and I had to be just as careful when trying to break the mastic hold on the glass. With a sigh of relief it came free and the glass was lifted out. The worst part of the job was to remove all the old mastic and rubber that had been stuck on the front. The leak by the way didn’t look to be coming from the glass, the vents at the front obviously let the water in and it runs of to the sides were it sits unless it runs out through a drain channel. As a result the cowl will go rusty in the corners so when it rains the channel to drain away is circumvented and goes inside the car. I know I may have to replace the cowl, but that needs to be inspected for repair or replace shortly. The link for the full process of getting the glass out and more pictures can be found here, or the quick links at the bottom.
The rear glass being removed.
The front glass being removed showing the generous usage of mastic.
Today I was cleaning up the steering column. This needs to be stripped back to bare metal in order for it to be painted and coordinated to the interior colours. The column was in a bad way at the bottom end where it goes through the fire wall to the steering box. The grease now gone hard, dirt, grime and anything else had to be cleaned off. POR Strip was used and wire wool to get back to the metal. Inside the column was full of old grease and needed to be cleaned out as well. The steering wheel end has a collar which holds the horn assembly and the indicator lights stalk. The horn section I have thrown out as the wires were brittle and were on an old Grant Steering wheel which I want to replace with a nice wood one. My arms ache but it was a job worth doing. The final part is to coat it from rusting with Gibbs Brand Lubricant until it needs to be painted. I just love that Gibbs Brand, see here for my review and articles. The brackets and plates I will finish them next week.
The exciting news:
Now that my car is a shell with nothing in it or on it apart from the doors that is, we could well be putting her onto a rotisserie soon to allow me access to the underneath in order to clean it all up and look for the repairs needed. The rear quarter panel needs replacing and lining up with the door, once that is done the doors will come off as well to get to the pillars and work on them too.
Quick Links:
Front and Rear Glass can be found under Photo Menu – Glass Work – Front & Rear Glass or click here.
Steering column work is can be found under Photo Menu – Steering – Steering Gearbox & Column Renovation or click here.